Modular kitchen cost in India is usually quoted per sq ft of cabinet face area, and it is driven by three choices: the carcass board (MR, BWR or BWP plywood, HDHMR or particle board), the shutter finish (laminate, acrylic, PU or membrane) and the hardware (hinges, drawer systems, baskets). A laminate-on-plywood kitchen sits at the lower end and acrylic or PU on BWP ply with premium hardware at the top; exact rates vary a lot by city, brand and fabricator.
In this guide
- 1.How is modular kitchen cost per sq ft calculated?
- 2.How much does a modular kitchen cost per sq ft by material?
- 3.Which carcass material is best for a modular kitchen?
- 4.Laminate vs acrylic vs PU: which shutter finish should you choose?
- 5.How much do hardware and accessories add?
- 6.How much does a kitchen countertop cost?
- 7.How can you reduce modular kitchen cost without cutting quality?
- 8.Frequently asked questions
How is modular kitchen cost per sq ft calculated?
Most designers and fabricators in India price a modular kitchen per square foot of cabinet face area: the width of each run of cabinets multiplied by its height, added up for base units, wall units and tall units. Some quote per running foot instead, which hides the height. Always ask which method a quote uses before you compare two quotes.
Example: a 10 ft base run that is 2.8 ft tall is 28 sq ft; a 10 ft wall run that is 2.5 ft tall is 25 sq ft; one 2 ft × 7 ft tall unit adds 14 sq ft. That kitchen is about 67 sq ft of cabinets, before countertop, appliances and accessories.
Countertops, sinks, chimneys, hobs and special accessories are usually priced separately, so a low per-sq-ft rate is not the whole story.
How much does a modular kitchen cost per sq ft by material?
The table below shows how materials stack up. The per-sq-ft bands are typical market ranges for a finished kitchen (material plus fabrication and installation) and are only indicative: rates differ widely between cities, brands and fabricators. The live board prices let you check the material part yourself.
| Build | Carcass + shutter | Typical range per sq ft | Board price today |
|---|---|---|---|
| Budget | Pre-laminated particle board or MR ply with laminate | ₹1,000–1,500 | from ₹1,290 / sheet |
| Standard | BWR ply carcass, laminate shutters | ₹1,400–2,200 | from ₹2,280 / sheet |
| Water-safe | BWP ply carcass, laminate or HDHMR shutters | ₹1,800–2,800 | from ₹3,050 / sheet |
| Premium | BWP ply carcass, acrylic, PU or glass shutters | ₹2,500–4,500+ | from ₹2,480 / sheet |
Board prices are per 8×4 ft sheet (32 sq ft). One sheet does not make 32 sq ft of cabinet face: each cabinet has sides, a back, a base, shelves and a shutter, so a kitchen uses several square feet of board for every square foot of front.
Which carcass material is best for a modular kitchen?
The carcass is the box behind the shutter, and it decides how long the kitchen lasts. For Indian kitchens, which are washed and mopped often, the safe default is BWP plywood for the sink base and all base units, and BWR or BWP for wall units. Our guide to BWP vs BWR vs MR plywood explains the grades.
HDHMR is a dense engineered board that machines cleanly; many fabricators use it for shutters and some for carcasses. Pre-laminated particle board is the cheapest finished board but swells if water gets into an edge, so keep it to dry areas and rental or budget projects. WPC is waterproof and good under sinks, but heavier.
Carcass and shutter boards
Live prices, excl. GSTPhenolic-bonded ply for wet areas, outdoor furniture and kitchen bases. Price is for 18 mm, 8x4 ft.
For kitchens and bathroom vanities that see water. Price is for 18 mm, 8x4 ft.
Dense, termite-resistant board for kitchen shutters and CNC routing. 18 mm, 8x4 ft.
Ready-finished board for office tables, storage and budget modular units. 18 mm, 8x4 ft.
Waterproof, termite-proof board for bathroom vanities and outdoor units. Can be routed and screwed.
Edge tape to match laminates, for machine or hand application. 22 mm x 0.8 mm, 200 m roll.
Laminate vs acrylic vs PU: which shutter finish should you choose?
Laminate is the most popular choice: durable, scratch-resistant, easy to clean and available in hundreds of wood, solid and stone looks. It is also the most affordable. Acrylic gives a mirror-gloss finish that looks premium and wipes clean, but shows fingerprints and fine scratches and costs more. PU (polyurethane) paint gives a seamless lacquered look in any colour; it is the most expensive and needs a skilled paint shop.
Membrane (PVC foil) allows routed, profiled shutters at mid-range cost but can peel near heat. Glass works for a few wall-unit shutters as an accent.
Shutter finishes
Live prices, excl. GSTWood, solid and stone-look laminates for wardrobes and kitchens. 8x4 ft, suede or gloss finish.
Mirror-gloss acrylic sheet for kitchen shutters and feature walls. 8x4 ft, scratch-resistant film.
Real teak, walnut and oak veneer on base ply for premium doors and panels. Price varies by species.
How much do hardware and accessories add?
Hardware is where kitchens quietly become expensive. A basic kitchen uses standard hinges and ball-bearing drawer channels; a premium kitchen uses soft-close hinges, tandem drawer systems, pull-out baskets and corner carousels. Compare the live prices below: a single tandem drawer set costs several times a pair of telescopic channels, and a kitchen can have 6–10 drawers.
Good hardware is worth it on the drawers you use most (cutlery, utensils, pots). For rarely opened wall units, standard soft-close hinges are enough.
Hinges, drawers and baskets
Live prices, excl. GSTClip-on hydraulic hinge for kitchen and wardrobe shutters. 35 mm cup, nickel finish.
Full-extension drawer slides, 45 kg load. Sold per pair. Price for 18 inch.
Metal-sided drawer kit with soft-close runners for modular kitchens. Price for 500 mm, 2 sides + runners.
Wire baskets for plates, cups and cutlery in modular kitchens, with soft-close runners.
How much does a kitchen countertop cost?
Granite is still the most common countertop in Indian kitchens because it is hard, heat-resistant and affordable. Black and common grey granites cost the least; exotic colours and quartz cost more. Countertops are priced per sq ft for the slab plus fabrication per running foot for cutting, sink and hob cut-outs, edge profile and polishing.
Countertop
Live prices, excl. GSTIndian granite for kitchen tops, stairs and door frames. Price is for black and common greys.
Kitchen tops cut to template with sink cut-outs, edge profile and polishing. Price per running foot.
How can you reduce modular kitchen cost without cutting quality?
Save where it does not show, and spend where water and daily use hit hardest.
- Use BWP only for the wet zone (sink base, dishwasher and RO units) and BWR elsewhere, if the client's budget is tight.
- Choose laminate shutters with one acrylic or glass accent instead of an all-acrylic kitchen.
- Limit premium drawer systems to the two or three drawers used daily.
- Keep cabinets to standard widths (300, 450, 600, 900 mm) so they can be CNC-cut efficiently.
- Buy boards, laminates and hardware together for the project to get better slab pricing.
- Get every quote on the same basis: per sq ft of face area, with countertop and accessories listed separately.
Browse everything for interior designers and furniture makers, or send us your BOQ for one consolidated quote.
Frequently asked questions
What is the cost of a modular kitchen per sq ft in India?
Indicative finished rates run from roughly ₹1,000–1,500 per sq ft of cabinet face for budget particle-board or MR-ply kitchens to ₹2,500–4,500 or more for acrylic or PU on BWP plywood. Rates vary widely by city, brand and fabricator.
Which material is best for a modular kitchen in India?
BWP plywood for the sink base and base units, BWR or BWP plywood for wall units, and laminate or acrylic shutters. HDHMR is a good option for shutters, and WPC works well under the sink.
Is HDHMR better than plywood for kitchens?
HDHMR is dense, smooth and machines cleanly, which makes it good for shutters and CNC work. BWP plywood holds screws better over the long term and is lighter, so many designers use BWP for carcasses and HDHMR for shutters.
Is acrylic better than laminate for kitchen shutters?
Acrylic looks glossier and more premium, but it costs more and shows fingerprints and fine scratches. Laminate is tougher, cheaper and comes in more designs. Both are good choices; it depends on look and budget.
Does modular kitchen cost include the countertop and chimney?
Usually not. Most quotes cover carcass, shutters and basic hardware; the countertop, sink, chimney, hob and premium accessories are priced separately. Always ask for an itemised quote.
Get this list priced in 24 hours
Add the items to your requirement list or just tell us what you need. One quote in 24 hours, zero commission, GST invoice.
Prices on this page come live from the YesBatch catalogue, exclude GST and are for the listed minimum order. Your quote confirms the final price for your quantity, city and delivery date. For the full range, browse supplies for interior designers.